Be Careful How To Replace Your Own Car Battery, Do It With The Following Steps

0 Shares

Multymeter.com – he car’s electrical system is powered by the battery, so when the car’s battery is not working properly, there are bound to be various systems that are difficult to start. Such as problems with the starting system, ignition system and various other parts of the car, if the battery is considered to be damaged, it should be replaced immediately.

The important function of the existence of an automobile battery is to provide the electrical power needed by almost all parts of the automobile.

So, without a normally functioning battery, it will be very impossible for the car to start or even drive on the road.

The presence of a battery causes the lights to shine brightly and the horn to sound loudly. Recognizing a car battery that has a diminished function is actually not difficult.

If the battery is not working as it should, the car’s motor traction will weaken. The lights will also not be as bright as they used to be. Then, the faint sound of the horn becomes the most obvious characteristic you can feel.

Don’t take long to replace the battery with a new one so that all the components of the car can function properly. The driving experience will also be more comfortable, safe and quiet without worrying too much.

Replacing the car battery is not as easy as we think, just remove the car battery and then replace it. To remove the battery properly, you should not remove cables, bolts or anything connected to the battery carelessly.

Steps to remove the correct car battery

1.Carefully remove the battery.

The battery is a component of the car that is used to distribute electrical power to various parts, so what will happen if the battery is not released properly? The vehicle will definitely not be able to operate normally as it should.

2. Prepare tools Removing the right car battery, of course, requires the right equipment. Some of these tools may already be familiar to you, such as a small screwdriver, pliers, a wrench or wrench that fits the battery bolts, and other tools if necessary. Usually wrench no. 10 or no. 12.
3. Make sure the ignition is turned off. To avoid a short circuit, the technician must first turn off the car engine and make sure the ignition is in the off position. Sometimes, in some automobiles, a throttle reset occurs when the battery is removed and installed.
4. Focus on the negative pole As a component for providing electrical power, the battery has a negative and positive pole. For the first step, the technician will normally focus on the negative pole of the battery first. The technician will begin by removing the cables, bolts and clamps from the negative pole. Why does the negative pole have to be removed first? This is to avoid short circuits, electrical shorts or sparks that are dangerous to the battery and also to the vehicle’s engine system.
5. Begin disconnecting the positive pole section. If you have removed all the negative pole parts, the technician will continue the process of removing the battery from the positive pole.
6. Lift the battery slowly and perpendicularly. When all cables, clamps and the two poles of the battery are no longer connected to the other parts, the battery can be lifted. The process of lifting this battery should be done slowly and in an upright position. The main reason it has to be slow and perpendicular is to avoid spilling the liquid inside the battery. If water from the battery hits other metal components, direct corrosion will occur. This is why technicians need to lift it slowly but surely. Once the battery has been successfully removed, the process of removing the battery from the car will be completed.

How Replace a Car Battery

After knowing how to remove the correct car battery, it is also necessary to know the steps to install the correct battery so that the car battery is securely fastened.

1. Place the battery in an upright position The first battery installation is done by placing the battery in an upright position so that the battery fluid does not spill out. Place the battery in the holder slowly. Make sure that the battery is stored in the holder correctly so that it does not shake easily and the liquid inside will spill out. The important thing to do before reinstalling the car battery is to clean the battery terminals from dirt deposits.
2. Installing the positive cable Next, connect the positive pole cable first. Unlike when removing a car battery, where the negative pole must be removed, when installing a car battery it is the positive pole cable that must be connected first to avoid sparks. Note that placing the positive pole near metal components will generate sparks when the negative pole is applied first. This will of course have an impact on the occurrence of a short circuit in the car engine.
3. Installation of the negative cable
4. Then proceed with the installation of the negative wire. When installing the negative cable, sparks will occur, but do not worry, these sparks are not dangerous and cause a short circuit.These sparks are normal when connecting the negative pole. The sparking will stop if the installation process of the car battery is done correctly.
5. Checking cables and clamps If so, make sure that all cables and clamps have been installed perfectly. Don’t leave anything loose or improperly clamped, the car will definitely not start when you try.

Start the car engine To check that the battery is perfectly installed, try to start the car engine, if the engine can start normally as before, it indicates that the car battery installation process has been completed correctly and properly. Hopefully, the above tips on how to remove a car battery can add more insight into the world of automobiles, especially automobiles. Keep the car in top condition so that there are no problems on the road.***